1. Refrigerator placement

(1) This Low Failure Rate Tube Ice Machine should be placed in a place where air is circulated and cleaned around.

(2) This machine should not be placed in the open air, and should not be exposed to direct sunlight or rain. You can’t get close to the heat source around.

(3) The environment in which the machine is used must not be lower than 5 ° C and not higher than 38 ° C.

(4) There should be enough space around the Reliable Performance Tube Ice Machine, especially the back can not be less than 250mm. So that the machine is cooling.

(5) Please adjust the anchor screw on the bottom of the machine to ensure the level of the machine is stable.

2, the installation of the water system

(1) Please connect the water source that meets the local drinking water standard.

(2) Attach a filter if necessary to increase the drinking standard of water.

(3) The water supply system must meet the following conditions:

a, the water temperature is at least 2 ° C, the maximum is not more than 38 ° C

b, the water pressure is at least 0.02Mpa, the highest is 0.8Mpa

3, the installation of the power supply

(1) The power supply must be the same as indicated on the machine nameplate.

(2) All lines must comply with national standards.

(3) It must be reliably grounded, and the grounding wire must meet electrical standards.

(4) The voltage fluctuation shall not exceed ±10% of the rated voltage.

Which Flake Ice Machine 1 Tons is easy to use? There are many average old manufacturers are basically the same in technology. There is not much difference, but the strength and qualification of different ice machine manufacturers are different. Which ice machine is easy to use, how to choose?

Choose according to the brand – which ice machine is easy to use

There are many brands of ice machine manufacturers, reliable quality, leading brands of technology, snowman, snow deer, Wanlidu and other manufacturers.

Choose according to the cooling method – which ice machine is easy to use

Ice-making machines are commonly used in air-cooling machines, water-cooled ice machines.

Air-cooled ice machine, small footprint, no need for water resources, low operating costs, easy to install and use. It can be used as long as the power is turned on. Air-cooled without water cooling and ice making effect.

Scope: Small ice machines, or areas where water is scarce.

The water-cooled ice machine needs to install a waterway and a water supply system. The initial cost is higher, and the cooling effect is better than the air-cooling effect.

Scope of application, medium and large ice machines, air cooling is recommended in areas where water is scarce.

Choose according to the application – which ice machine is easy to use

1. tube ice machine.

2, commercial industry, flake ice machine, ice brick machine, tube ice machine.

1 After opening the outer casing of the Reliable Performance Tube Ice Machine, the same refrigeration system, not to mention what brand of compressors, condensers, desiccants, evaporators, intelligent electronic boards, etc. are used by various manufacturers. As far as the internal design is concerned, the quality design of the high-quality ice machine is strict, the lines are arranged neatly and orderly, and the parts that are easy to be wet or wading (especially the electronic control system) will be specially waterproofed, which can not only withstand the long-term high temperature. The test, even at 40 degrees high temperature, the ice making speed is still unaffected, and the machine’s normal operation and user safety are absolutely guaranteed. Ordinary or inferior ice machine, generally has small rear space, disordered line arrangement, poor heat dissipation, poor water resistance or no waterproof treatment at all; after several months or six months of operation, in high temperature weather, the ice making speed is obvious. Reduce, and even stop the damage, bring unnecessary troubles and economic losses to the user.

2 The high-quality Reliable Performance Tube Ice Machine opportunity fully considers the rear cooling space of its internal components; the precise and reasonable design makes the ice making speed faster and achieves the goal of energy saving and environmental protection. For the convenience of post-maintenance and maintenance, most of them will adopt the hanging type assembly mode. External use and up to 4 screws can be disassembled and maintained quickly, saving time and no need to move the machine. It can be cleaned and maintained in 15 minutes.

1. Flake Ice Machine application in the processing of aquatic products: flake ice can reduce the temperature of processing medium, washing water and aquatic products, prevent bacteria from growing, and keep fresh in the processing of aquatic products.

2. Application of the processing of meat products: The flakes that meet the hygienic standards are mixed with meat and stirred. In order to achieve the purpose of cooling, preservation.

3. Application of food processing: such as in the production of bread, when stirring or twice creaming, use tablet ice to quickly cool down to prevent fermentation.

4. Application in supermarkets and aquatic products market: for the preservation of aquatic products, display, packaging, etc.

5. Flake Ice Machine application of vegetable processing: The process of harvesting agricultural products and vegetables uses flake ice to reduce the metabolism of agricultural products and the growth rate of bacteria. Extend the shelf life of agricultural products and vegetables.

6. Application of long-distance transportation process: products such as ocean fishing and vegetable transportation that need to be cooled and preserved are more and more widely used in long-distance transportation to cool and preserve fresh flakes.

7. It is also widely used in laboratories, pharmaceuticals, chemicals, artificial ski resorts and other industries.

8. Application in concrete engineering: When the concrete is poured in a wide range in the hot season, the pouring temperature of the concrete must be effectively and reasonably controlled. The flake ice + cold water stirring is an effective way.

1. The Flake Ice Machine should not be placed in an open air environment. It should be installed in a safe, clean and well ventilated environment, and should not be exposed to direct sunlight or rain.

2, the ice machine can not be close to the heat source, the use environment can not be lower than 5 ° C, not higher than 40 ° C, so as not to affect the heat dissipation of the condenser too high temperature, can not achieve a good ice making effect.

3. The Flake Ice Machine should be installed on a stable platform and adjust the anchor screws at the bottom of the machine to ensure the level of the machine. Otherwise, it will cause no ice and noise during operation. Space should be left around. In order to facilitate heat dissipation, the left and right spaces on the left side of the machine should not be less than 150mm.

4, the ice machine should use the specified independent power supply in line with national standards, the power supply should ensure reliable grounding, and equipped with fuses and leakage protection switches, etc., voltage fluctuations should not exceed ± 10% of the rated voltage.

Different Seafood Markets Flake Ice Machine mechanisms require different amounts of ice. Here are some of the commonly used ice machines, and how long it takes for them to make one ice.

Fake ice machine is a transparent small square shape. It is mainly used for strict requirements on ice. It must reach the eating environment. Generally, ice is produced in more than 10 minutes.

The Flake Ice Machine is commercially edible and has a transparent cylindrical shape. It takes about 15 minutes to make a single film.

The flake ice machine is mainly used for commercial and industrial use. The ice is in the form of flakes. The thickness of the borneol is about 1.5-2.2mm, and the flake ice machine can be iceed after 1-3 minutes.

Flake Ice Machine mainly used in commercial, industrial, ice-shaped large rectangles, or large ice bricks, respectively, size, 5KG piece, 10KG piece, 20KG piece, maximum 100 kg piece, the smaller the ice block, the more ice time Short, the ice is bigger, the longer the ice is, the ice is 6-8 hours for 30 kg, and the block is for 24 hours for 100KG.

1. Application in the processing of Flake Ice Machine for aquatic products: flake ice can reduce the temperature of processing medium, washing water and aquatic products, prevent bacteria from growing, and keep fresh in the processing of aquatic products.

2. Application of the processing of meat products: The flakes that meet the hygienic standards are mixed with meat and stirred. In order to achieve the purpose of cooling, preservation.

3. Application of food processing: For example, in the production of bread, when stirring or twice creaming, use a piece of ice to quickly cool down to prevent fermentation.

4. Application in supermarkets and aquatic products market: for the preservation of aquatic products, display, packaging, etc.

5. Application of Vegetable Preservation Flake Ice Machine: The process of harvesting agricultural products and vegetables uses flake ice to reduce the metabolism of agricultural products and the growth rate of bacteria. Extend the shelf life of agricultural products and vegetables.

6. Application of long-distance transportation process: products such as ocean fishing and vegetable transportation that need to be cooled and preserved are more and more widely used in long-distance transportation to cool and preserve fresh flakes.

7. It is also widely used in laboratories, pharmaceuticals, chemicals, artificial ski resorts and other industries.

8. Application in concrete engineering: When the concrete is poured in a wide range in the hot season, the pouring temperature of the concrete must be effectively and reasonably controlled. The flake ice + cold water stirring is the most effective way.

The flake ice has obvious advantages compared with the traditional type of briquettes (bulk ice) and snow flakes. It has the advantages of being dry, not easy to agglomerate, good fluidity, good hygienicity, large contact area with fresh-keeping products, and not easy to damage fresh-keeping products. Many industries are the preferred products to replace other types of ice.

Through the inlet valve on 2.5 Tons Flake Ice Machine, the water automatically enters a water storage tank, and then pumps water to the diverter through the water pump. The diverter pipe uniformly flows the water to the evaporator cooled by the low-temperature liquid refrigerant, and the water is cooled to the freezing point, which is cooled to the freezing point. The water will solidify into ice, and the water that has not been frozen by the evaporator flows into the water reservoir again, and the circulation is resumed by the water pump.

When the ice cube in the Start And Stop Automatically Flake Ice Machine reaches the required thickness, it enters the deicing state, and the high pressure hot gas discharged from the compressor is led to the evaporator through the reversing valve to replace the low temperature liquid refrigerant. This forms a water film between the ice cube and the evaporator, which leaves the ice cubes out of the evaporator, and the ice cubes fall freely into the ice storage tank by gravity.

An Fresh Water Flake Ice Machine is a refrigeration machinery that produces water by cooling water from a refrigeration system through an evaporator.

The chilled water of the water storage tank is continuously circulated through the plate or the compartmentalized evaporator by the water pump; after the compressor is operated, the suction-compression-exhaust-condensation (liquefaction)-throttle–in the evaporator is -10 to – 18 degree low temperature evaporation endothermic vaporization, chilled water continuously condenses into ice layer on the surface of lower temperature evaporator at 0 degree water temperature in Flake Ice Machine 1.5 Tons, when the ice layer condenses to a certain thickness, the evaporation temperature of the refrigerant reaches temperature control After setting the temperature, the defrosting solenoid valve is often turned on, and the heat pump is used to de-ice, and then the next cycle is realized